BT200 BRAIN手操器是一種便攜設備，針對采用BRAIN通信協議的設備和現場儀表，對其進行設定、更改、顯示、診斷和打印配置或校正信息。與橫河電機所有的通信設備一起使用

BT200 BRAIN手操器是一種便攜設備，針對采用BRAIN通信協議的設備，對其進行設定、更改、顯示和打印參數，如工位號、輸出模式、范圍等。這款手操器還可以監視I/O值和自診斷結果，設定恒定電流的輸出以及進行調零。當系統啟動或維持操作狀態時，只需連接設備的4~20 mA DC信號線或ESC(信號調節通信卡)上的專用接口，即可執行這些功能。
  特性: BT200 BRAIN手操器 As a portable terminal, the Model BT200 BRAIN TERMINAL is used in combination with equipment using brain communication for setting, changing, displaying and printing out parameters such as tag number, output mode, and range, through simultaneous communication. It also monitors I/O values and self-check results, sets constant-current output , and allows zero adjustments. The Model BT200 BRAIN TERMINAL is used by connecting it between 4 to 20 mA DC signal transmission lines of the equipment or to a dedicated connector on the ESC (Signal Conditioner Communication Card) when the system is started up or maintained.
    FEATURES
  Online monitoring and communication
The modulated communication signal does not interrupt the 4 to 20 mA DC signals during communication.
  Common to all Yokogawa’s equipment
The Model BT200 BRAIN TERMINAL works with all equipment that uses BRAIN communication.
  Easy of use
A large display (21 characters by 8 lines) eases setup and alteration procedures in English prompting interactive sequences.
   Diagnostics/security with error messages
• Self-check function • Security code protection of setpoints • Low battery voltage alarm • Automatic power-off
   Printer
(BT200-P00) Printer prints out tag numbers and other parameters on the spot.

STANDARD SPECIFICATIONS Equipment Specifications Applicable Equipment: [Field Instruments] DPharp ADMAG YEWFLO YTA [Signal Conditioner] Signal Conditioner for CENTUM Communication Specification: Yokogawa original protocol Modulation: Burst modulation 0: 2400 Hz 1: Signal without carrier Baud rate:1200bps Communication signal: host to device: +/- 0.5 V (load resistance 250 ) device to host: +/- 2 mA Communication Line: [Field Instruments] Load resistance: 250 to 600 (including cable resistance) Load capacitance: 0.22 μF or less Load inductance: 3.3 mH or less Power line spacing: 15 cm (6 inch) or more (Avoid parallel wiring.) [Signal Conditioner] Use dedicated cable Line Length: [Field Instruments] Up to 2 km (1.24 mile) (0.75 to 1.25 mm2 instrumentation cable) [Signal Conditioner] 1.1 m with dedicated cable Communication Signal Connection: Dedicated cable, 1.1 m long (3.6 ft) 
         EMC Conformity Standards EN61326-1 Class A, Table2 (For use in industrial locations) Display: LCD dot matrix, 21 characters×8 lines Controls: Membrane switches (four function keys, 20 general operation keys, and one power switch) Printer (BT200-P00): Thermal paper type Power Supply: Five AA 1.5 V dry alkali batteries (LR6/AM3 (N)), or Five AA 1.2 V Ni-MH batteries (HR6/AA) Dimensions: BT200-N00 . . . 228×110×51 mm (9.0×4.3×2.0 inch) BT200-P00 . . . 321×110×61 mm (12.6×4.3×2.4 inch) Approximate Weight: BT200-N00 . . . 510 g (1.12 lb) BT200-P00 . . . 700 g (1.54 lb) 
        NORMAL OPERATION CONDITIONS BT200-N00 Ambient Temperature: -15 to 55°C (5 to 131°F) Ambient Humidity: 5 to 95%RH at 40°C (104°F) BT200-P00 Ambient Temperature: 0 to 50°C (32 to 122°F) Ambient Humidity: 30 to 80%RH at 40°C (104°F) n STORAGE CONDITIONS Ambient Temperature: -15 to 60°C (5 to 140°F) Ambient Humidity: 5 to 95%RH at 40°C (104°F) 30 to 80%RH at 40°C (104°F) (with printer) n ACCESSORIES l Communication Cable: Two cables, one with alligator clips and one with IC clips (both snap-removable) l Handy carry case
        n FUNCTIONAL SPECIFICATIONS Basic Functions: l Setup, alteration, and display of parameters BRAIN communication. : constant current output : Zero point adjustment Additional Functions: l Batch upload/download of data l Setpoint Protection: Security code entry is required to alter setpoints. l Battery Alarm: An alarm message appearing on the LCD announces low battery voltages. l Automatic Power-off: The terminal is switched off automatically if no key access is made for approximately 5 minutes. l LCD contrast adjustment l Printing (BT200-P00) Printout Information l All parameter lists l Parameter list within each menu item l Setup change data list l Uploaded data list l Display images l Self check list